Services
Home batteriesSolar + battery systemsSolar panelsAdd a battery to solarEV chargersMain panel upgradesAll services →
Areas we serve
San FranciscoSan FranciscoNorth BayEast BayPeninsulaSouth BaySee every city →
Resources
Home & roof · Guide

Solar panel maintenance: what panels actually need

Very little, which is the good news. When to clean, how to spot a fault early, and the parts that wear out before the panels do.

SolarUnion Editorial TeamIndependent solar and battery guides
Updated 6 min read
In this article
The short answer
  • Panels have no moving parts. Most Bay Area systems need little more than a glance at the monitoring app and an occasional rinse.
  • Clean when output drops and the glass is visibly dirty, usually late in the dry season. Use a soft brush and plain water, never a pressure washer.
  • Inverters are the part most likely to need replacing during the system's life. Check the warranty terms you have.

Solar panels are about as low-maintenance as a home system gets. They have no moving parts, they are built to sit outdoors for decades, and California's winter rain does a lot of the cleaning for free. Maintenance is mostly about noticing problems early so a fault does not quietly cost you a season of production.

Cleaning: when and how

Dust, pollen, ash from fire season and bird droppings all cut output a little. On a tilted roof, rain washes most of it off. The case for cleaning is strongest at the end of the long dry season, on flat or low-tilt arrays where dirt does not run off, and near highways, farms or construction.

  • Check first. Compare this month's production with the same month last year. If it is down and the glass looks dirty, clean.
  • Use the gentle method. A soft brush or sponge on an extension pole and plain water, ideally in the early morning when the glass is cool.
  • Avoid pressure washers, abrasive pads, harsh detergents and hard water that leaves spots.
  • Stay off the roof unless you have proper fall protection. A professional cleaning is inexpensive compared with a fall.

Monitoring is the real maintenance

Every modern system has a monitoring app. Ten seconds a week is enough: is it producing, and does today look like a normal day for the weather? Systems with microinverters or optimizers show each panel separately, which makes a single failed unit easy to spot.

Set an alert. Turn on the app's notifications for zero production or communication errors. A system that silently goes offline in May can cost hundreds of dollars before anyone notices.

What wears out, and when

ComponentTypical lifeWhat to know
Panels25 to 30+ yearsLose a small fraction of output each year; warranties typically guarantee 80 to 90 percent after 25 years
String inverterAbout 10 to 15 yearsThe component most likely to be replaced once during the system's life
MicroinvertersOften warranted 25 yearsOne failure affects one panel, not the whole array
Battery10 to 15 years under warrantyCapacity declines gradually; check the warranty's end-of-term capacity
Roof attachmentsLife of the roofCheck flashing whenever the roof is inspected
Typical ranges; your equipment's datasheets and warranties govern.

A once-a-year checklist

  • Compare annual production with the design estimate and the prior year.
  • Look at the array from the ground for cracked glass, debris, sagging wiring or nesting birds.
  • Trim trees that have grown into the array's sun.
  • Check the attic below the array after the first big rain for any sign of moisture.
  • Confirm the battery's backup reserve setting before PSPS season.
  • Keep warranty documents and installer contact details where you can find them.

Production dropped and you don't know why?

We troubleshoot existing systems, including ones we didn't install.

Get help

When to call a professional

  • Production at zero, or an inverter or battery showing a fault light.
  • One panel or string far below the others for weeks.
  • Any sign of a roof leak near the array.
  • Damage after a storm, fire or tree fall.
  • Squirrels or birds under the array; mesh guards stop chewed wiring.

If your original installer has gone out of business, your equipment warranties from the manufacturers still apply. A qualified installer can file the claim and do the work.

Keep your system producing.

Diagnostics, repairs and battery add-ons for existing solar.

Contact us
GuidesGet my estimate