Services
Home batteriesSolar + battery systemsSolar panelsAdd a battery to solarEV chargersMain panel upgradesAll services →
Areas we serve
San FranciscoSan FranciscoNorth BayEast BayPeninsulaSouth BaySee every city →
Resources
Batteries · Explainer

AC-coupled vs DC-coupled batteries

Two ways to wire a battery to solar. Which one fits depends mostly on whether your panels are already on the roof.

SolarUnion Editorial TeamIndependent solar and battery guides
Updated 6 min read
In this article
The short answer
  • AC-coupled batteries have their own inverter and connect on the house side. They are the usual way to add a battery to existing solar.
  • DC-coupled batteries share one hybrid inverter with the panels. They are common for new solar plus battery systems and lose a little less energy charging from solar.
  • The efficiency gap is real but small. Fit with your existing equipment, backup power and cost usually decide.

Solar panels make direct current (DC). Your home runs on alternating current (AC). Batteries store DC. Every solar and battery system has to move energy between those two forms, and "coupling" describes where the battery joins the system. That one wiring choice affects efficiency, cost, and how easily a battery fits next to panels you already own.

Why the inverter is the whole story

An inverter converts DC to AC. Each conversion loses a few percent of the energy. In an AC-coupled system, solar power is converted to AC by the solar inverter, then back to DC to charge the battery, then to AC again when the battery powers the home. In a DC-coupled system, solar DC flows straight into the battery through a shared hybrid inverter, and is converted to AC only once, when you use it.

Side by side

AC-coupledDC-coupled
Where the battery connectsHouse side, after the solar inverterPanel side, through a shared hybrid inverter
Conversions from solar to battery to homeThreeOne to two
Round-trip efficiency from solarA few points lowerA few points higher
Best forAdding storage to existing solarNew solar and battery installed together
Existing inverterStays in placeUsually replaced by the hybrid inverter
ExamplesEnphase IQ Battery 5P; Powerwall 3 added to an existing arrayPowerwall 3 with new solar wired to its built-in inverter; other hybrid inverter systems
Efficiency differences vary by equipment; compare manufacturer datasheets for the exact figures.

Adding a battery to solar you already have

If your panels are on the roof and working, AC coupling is almost always the practical choice. The battery and its inverter install beside your existing system without rewiring the array or replacing a solar inverter that may still be under warranty. That is especially relevant for Bay Area homes on NEM 1 or NEM 2, where the goal is often backup power for PSPS shutoffs without disturbing a favorable billing arrangement.

The energy lost to the extra conversion matters less than it sounds. A few percent of the solar you store is a small number next to the value of keeping your existing equipment and having power during an outage.

NEM 2 homes, ask first. Adding a battery to an existing system can change your interconnection paperwork. Ask your installer in writing how the change keeps your legacy NEM 2 status.

New solar and battery together

When both go in at once, DC coupling through a hybrid inverter often means fewer boxes on the wall, one conversion fewer, and a lower equipment cost. The trade-off is concentration: if the hybrid inverter needs service, solar and battery pause together. Microinverter systems take the opposite approach, with an AC-coupled battery and an inverter under every panel, which spreads that risk.

How to choose

  • Existing solar: start with AC coupling unless your inverter is failing or out of warranty anyway.
  • New system: compare a DC-coupled hybrid design against a microinverter plus AC battery design on price, backup power and shading on your roof.
  • Heavy loads: check continuous and peak power ratings, not only capacity, if you want a heat pump or well pump on backup.
  • Older panels: confirm your service panel can take another backfeed breaker, or plan for load management.

Get the right battery for the solar you have.

AC or DC, sized from your PG&E data.

Get my estimate
GuidesGet my estimate